АвтоАвтоматизацияАрхитектураАстрономияАудитБиологияБухгалтерияВоенное делоГенетикаГеографияГеологияГосударствоДомДругоеЖурналистика и СМИИзобретательствоИностранные языкиИнформатикаИскусствоИсторияКомпьютерыКулинарияКультураЛексикологияЛитератураЛогикаМаркетингМатематикаМашиностроениеМедицинаМенеджментМеталлы и СваркаМеханикаМузыкаНаселениеОбразованиеОхрана безопасности жизниОхрана ТрудаПедагогикаПолитикаПравоПриборостроениеПрограммированиеПроизводствоПромышленностьПсихологияРадиоРегилияСвязьСоциологияСпортСтандартизацияСтроительствоТехнологииТорговляТуризмФизикаФизиологияФилософияФинансыХимияХозяйствоЦеннообразованиеЧерчениеЭкологияЭконометрикаЭкономикаЭлектроникаЮриспунденкция

PROTOTYPE BRUSHLESS MOTOR OBJECTIVES

Читайте также:
  1. AC Motors
  2. Der Elektromotor
  3. Der Verbrennungsmotor
  4. DIAGRAMA CIRCULAR PARA MOTOR ASINCRONICO
  5. Electric generators and motors
  6. Electric motor
  7. G Motorola DynaTAC 8000 Range. Released: 1984 to 1987
  8. L’VIV – BRODY MOTORWAY
  9. L’VIV – KRAKOVETS’ MOTORWAY
  10. MOTORWAY AND MAIN HIGHWAYS
  11. Rekat Prototype

Top quality brushless motor
Speed feedback sensors built into controller
Top quality brushless controller
Best available power supply (even better if it can run from battery)
High quality motor bearing
RPM approx 300 rpm would be ideal (for similar size pulley as we use at the moment)
Small size and high momentum and quick start up time
Extra low vibration needed

Ideally we need a feedback check on the motor to maintain constant speed, a high quality brass bush bearing …or ball raced…should give little or no noise…

Especially if the motor RPM is low …even less vibrations/hum

High filtered mains power supply is expensive and in some cases unreliable …new lithium polymer or NIMh batteries will give stable power. So the operating voltage of the motor needs be very low…. and the big plus is that the power supply only needs be a simple charger …like a Nokia phone charger for example (just under 4volts for the NIMh batteries)

Plus.. in theory.. the more batteries you have the better!

Ideally we need the motor to fit inside existing space in all turntables…so little conversion is need to fit on any turntable

FLOPPY CONVERSION —–has all the above—–

BASIC FLOPPY DRIVE is very cheap…

But the electronics controlling it are very sophisticated and the bearing is very good quality… and can be replaced if necessary

Go to top

Remove the top cover:

Normally just a few screws …or in this case just a screwdriver to lift up the back ends

Remove the screws on underside to take bottom cover off

Go to top

Unit now needs the heads and metal floppy cage removed

@ The bottom 6 screws hold the PCB onto the metal frame

…Remove the 6 screws

Go to top

Now we have the basic PCB visible

Go to top

This is now getting to a stage we can almost test it…

The plastic strips on top of motor, I removed them with a sharp knife

(How to connect the correct pins and cheat the sensors will come later)

Go to top

Spindle simply pulls off J – this makes cleaning very easy

Motor magnet and main spindle removed for inspection

Go to top

Clock timer and processor controller now flipped under the motor board and test pulley fitted on top of spindle

We will be trimming the PCB smaller later

Go to top

neat!!! -WORKING PROTOTYPE –

The 33-rpm and 45rpm 2-step pulley made from ally (will be turned down to ½ the size seen here look below)

Also the PCB area will be trimmed down to much smaller

And to save time I have glued the pulley on with super glue….

…The tidy up will come much later!

I have already got the sizes I need for the 33 rpm…the 45-rpm I have just guessed for the moment!

Go to top

3.6volt NIMh battery powers this unit for days and days…current draw with the led fitted is 20ma ß- my meter must be faulty …surely!!

Go to top

CONCEPT—– Nokia charger (or similar) can recharge the batteries…

Also the unit can be used worldwide. Used with your own phone charger!

I’ll need a simple charge- cut off- circuit…. the parts are cheap

Go to top

BEARING removed …simple but high quality bush bearing with black nylon thrust plate…. we are going to isolate the main bearing from the PCB/…but still keep it earthed to the copper on the PCB (stops static)

Small amount of silicon rubber solution @ the bottom of bearing will isolate it much better @ this stage …plus the silicon will help make a seal to hold oil in our brass bush bearing

PULLEY tidied up- this 1 made from easy-machined aluminium 33 and 45rpm

Go to top

FITTING TO THE TEST BED

Go to top

Join pins 12 to 11 and 16 to 15 in the IDE connector…the power goes in the right hand side connector though the 5volt input

Go to top

We can see the 2 pins bent here and easy 4 or 5volt input

Go to top

Cheat the floppy insert sensors to make it think there is a floppy inserted

(you can stick them in with tape …or remove from PCB and put little shorts in

Go to top

Ok, here we are running a old LINN inner platter /LINN belt… and almost the same pulley size as LP12….

the unit also has a variable resistor fitted (MORE ON THIS IN A MIN)…
and this is currently working our test bed model

Go to top

I found this 800ohm resistor inline to the motor controller…

(by jumpering each resistor with a 1000ohm resistor to see if any speed change was possible)

Each floppy will be different…so if you want to try varying the speed you will need spend a few minutes checking


1 | 2 |

Поиск по сайту:



Все материалы представленные на сайте исключительно с целью ознакомления читателями и не преследуют коммерческих целей или нарушение авторских прав. Студалл.Орг (0.005 сек.)